Your Plumbing Crash Course: Tips for Installing a Bathtub
Your Plumbing Crash Course: Tips for Installing a Bathtub
Blog Article
Do you find yourself in search of advise concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably hard project. If the old tub is readily obtainable, the job can relocate rapidly; if you need to open up a wall surface to get rid of the old bathtub as well as position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and set in the new one. Ensure you have certified on your own for the task and also fit attempting it. Instead of employing a contractor to take control of a halfway-completed job, it is far better to take into consideration employing one prior to you begin. Possibilities are you may require an expert plumber to make tube links.
This article will assist you set up a new bath tub in your bathroom if you have actually currently gotten a new bathtub and do not need to change the arrangement of your previous supply of water pipes.
Your devices and product list ought to make up the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of getting rid of the existing taps can be quite problematic because of the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washing machines remain in area in between the faucet and the sink. Protect the tap in place with the supplier offered backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The previous type needs to be linked to the tap finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Making use of the two wooden boards under its feet, place the bath tub in the needed placement. The wooden boards are practical in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the tub until the level reviews level.
To mount taps, fit all-time low of the outermost versatile faucet port to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Turn on the supply of water and also check all joints and also brand-new pipework for leaks and also tighten them if needed. Load the bathtub and likewise check the overflow electrical outlet and also the typical outlet for leaks.
Ultimately, fix the bath paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bathtub needs to wait till the bath tub has actually been utilized at least when as this will resolve it into its final position.
Preparing for the Installation
Firstly, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a rigid seal, creating the water to permeate the wall in between the bathroom and the tiling, resulting in complications with dampness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the bathtub is in usage. The sealer can break fairly early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily available on the market. It is a good idea to fit the tiles using water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent reader on How to Install a Bathtub Yourself, I imagined sharing that portion was important. Make sure you set aside a second to share this content if you appreciated it. I recognize the value of reading our article about How to Install a Bathtub.
Need help? Dial now. Report this page